كتيب زاوية طاحونة 9412 MA Skil

كتيب

7

inspect for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders away

from the plane of the rotating accessory and run

the power tool at maximum no load speed for one

minute. Damaged accessories will normally break apart

during this test time.

g) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron capable

of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping ying

debris generated by various operations. The dust mask

or respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

h) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of the

workpiece or of a broken accessory may y away and

cause injury beyond the immediate area of operation.

i) Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. A cutting accessory contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

j) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

k) Never lay the power tool down until the accessory

has come to a complete stop. The spinning

accessory may grab the surface and pull the power tool

out of your control.

l) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

m) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

n) 

materials. Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

2) KICKBACK AND RELATED WARNINGS

 Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the

binding.

 For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on the direction of the wheel’s movement at

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any



operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

dierent from those intended could result in a hazardous

situation.

5) SERVICE

a) 

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

1) SAFETY WARNINGS COMMON FOR GRINDING,

SANDING, WIRE BRUSHING, POLISHING OR

ABRASIVE CUTTING-OFF OPERATIONS

a) This power tool is intended to function as a grinder,



all safety warnings, instructions, illustrations and

Failure

to follow all instructions listed below may result in

electric shock, re and/or serious injury.

b) 

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

c) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can y apart.

d) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded or controlled.

e) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted



 Accessories

that do not match the mounting hardware of the power

tool will run out of balance, vibrate excessively and may

cause loss of control.

f) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pads for cracks, tear

or excess wear, wire brushes for loose or cracked

wires. If the power tool or accessory is dropped,

التقييم

المزيد عن دليل المستخدم هذا

نحن ندرك أنه من الجيد أن يكون لديك دليل ورقي لـ زاوية طاحونة 9412 MA Skil الخاص بك. يمكنك دائمًا تنزيل الدليل من موقعنا الإلكتروني وطباعته بنفسك. إذا كنت ترغب في الحصول على الدليل الأصلي، فنوصيك بالاتصال بـ Skil. قد يكون بمقدورهم تقديم دليل أصلي. هل تبحث عن دليل زاوية طاحونة 9412 MA Skil الخاص بك بلغة مختلفة؟ اختر لغتك المفضلة على صفحتنا الرئيسية وابحث عن رقم الطراز لمعرفة ما إذا كان متوفرًا لدينا.

تحديد

كافة الأدلة لـ زاوية المطاحن Skil
المزيد من أدلة زاوية المطاحن

الأسئلة المتداولة حول زاوية طاحونة 9412 MA Skil

يبحث فريق الدعم لدينا عن معلومات مفيدة عن المنتج وإجابات على الأسئلة المتكررة. وإذا وجت عدم دقة في أسئلتنا المتكررة، فيرجى إخبارنا بذلك عن طريق استخدام استمارة الاتصال بنا.

منتجات ذات صله

كتيب

زاوية طاحونة 9782 AA Skil

كتيب

Skil 9132 AA زاوية طاحونة

كتيب

زاوية طاحونة 9016 AA Skil

كتيب

زاوية طاحونة 1047 ME Skil

كتيب

زاوية طاحونة 1043 AA Skil

كتيب

زاوية طاحونة 9132 GA Skil

كتيب

Skil 9149 GA زاوية طاحونة

كتيب

Skil 9020 AA زاوية طاحونة

فئات ذات صلة