كتيب ماكينة تجليخ دوارة 7366 AA Skil

كتيب

6

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when original accessories are used

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A); wear

ear protection

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Regularly clean the power tool’s air vents (the

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards)

• When sanding metal, sparks are generated; do not use

dustbox and keep other persons and combustible

material from work area

• Do not touch the moving sanding sheet

• Do not continue to use worn, torn or heavily clogged

sanding sheets

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of sanding sheet 4

! disconnect the plug

! the dust suction requires the use of perforated

sanding sheets

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

• On/o switch

- switch on/o the tool by pushing switch A 2 forward/

backwards

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

• Dust suction 5

- empty dustbox B regularly for optimal dust pick-up

performance

- remove dustbox B by pushing knob C to the left and

hold it in that position while pulling dustbox B

backwards

- mount dustbox B by sliding it back until it clicks into

place

! do not use dustbox when sanding metal

• Pressure control 6 (7366)

Warns the user when applying too much pressure on the

tool while working (too much pressure reduces the

sanding performance)

- green light 1 turns on when running tool is placed on

workpiece

- green light 2 turns on in case of pressure

- green light 3 turns on in case of increased pressure

- red light 4 turns on when pressure is too high

• Speed control (7361)

For optimal sanding results on dierent materials

- with wheel E 2 you can set the desired sanding speed

- adjust speed to grit size used

- before starting a job, nd the optimal speed and grit by

testing out on spare material

التقييم

المزيد عن دليل المستخدم هذا

نحن ندرك أنه من الجيد أن يكون لديك دليل ورقي لـ ماكينة تجليخ دوارة 7366 AA Skil الخاص بك. يمكنك دائمًا تنزيل الدليل من موقعنا الإلكتروني وطباعته بنفسك. إذا كنت ترغب في الحصول على الدليل الأصلي، فنوصيك بالاتصال بـ Skil. قد يكون بمقدورهم تقديم دليل أصلي. هل تبحث عن دليل ماكينة تجليخ دوارة 7366 AA Skil الخاص بك بلغة مختلفة؟ اختر لغتك المفضلة على صفحتنا الرئيسية وابحث عن رقم الطراز لمعرفة ما إذا كان متوفرًا لدينا.

تحديد

كافة الأدلة لـ ماكينات تجليخ دوارة Skil
المزيد من أدلة ماكينات تجليخ دوارة

الأسئلة المتداولة حول ماكينة تجليخ دوارة 7366 AA Skil

يبحث فريق الدعم لدينا عن معلومات مفيدة عن المنتج وإجابات على الأسئلة المتكررة. وإذا وجت عدم دقة في أسئلتنا المتكررة، فيرجى إخبارنا بذلك عن طريق استخدام استمارة الاتصال بنا.

منتجات ذات صله

كتيب

ماكينة تجليخ دوارة 7380 AA Skil

كتيب

ماكينة تجليخ دوارة 7346 AA Skil

كتيب

ماكينة تجليخ دوارة 7335 AG Skil

كتيب

ماكينة تجليخ دوارة 7455 AA Skil

كتيب

ماكينة تجليخ دوارة 7366 AC Skil

كتيب

ماكينة تجليخ دوارة 7335 AA Skil

كتيب

ماكينة تجليخ دوارة 7361 AA Skil

كتيب

ماكينة تجليخ دوارة 7362 DA Skil

فئات ذات صلة