كتيب ماكينة قص الشعر FA-5676-1 First Austria

كتيب

4 5

2. Plug the Power Adapter into a

230V/50Hz AC outlet.

3. Switch the clipper ON and begin

trimming.

4. When finished, switch the clipper OFF

and unplug.

• Cordless

1. Charge the clipper according to

directions.

2. Remove the clipper from the Charging

Stand.

3. Switch the clipper ON and begin

trimming.

NOTE: If the battery has completely run out,

you can return to corded trimming. Connect

the Power Adapter cord plug to the clipper

and switch ON. If the clipper does not start

immediately when plugged in, switch it OFF.

Wait approximately 1 minute. Switch back

ON and begin trimming.

GUIDE COMB ATTACHMENT

The Guide Comb helps to guide hair to

cutting blades and gives you precise control

of hair lengths. It may be removed if you are:

• Defining/outlining hair line edges

• Trimming nape of neck

• Trimming with a Barber’s comb or fingers

To Remove the Guide Comb:

1. Be certain the clipper is in OFF position.

2. Gently pull the Guide Comb off the

clipper.

TRIMMING

1. Be certain the clipper is clean. If the

cutter blades are running slowly or

do not move, they may be dirty and

clogged. Clean the clipper following

MAINTENANCE instructions.

2. Seat person having hair trimmed in a

position where the top of the head is at

your eye level.

3. The hair should be clean, well combed,

tangle-free and dry.

4. Use the clipper with the Guide Comb.

5. Set the desired cutting length by turning

the bottom adjustment wheel.

6. Hold the clipper firmly but in a

comfortable grip.

• If you are not used to clipping hair, begin

with a higher setting and then reduce the

setting to avoid cutting more hair than

desired.

7. Start at the sides of the head. Move the

clipper up slowly against direction of hair,

lifting it up and outward through hair,

cutting a small amount at a time.

8. In between, shake or blow off the hair

from the clipper. If too much hair is

caught in the Guide Comb, remove and

clean it.

9. Regularly comb the hair in the style

desired during trimming.

Trimming without the Guide Comb

When using the clipper without the Guide

Comb, use a slow, smooth motion to prevent

trimming off more hair than desired.

Trimming with the Barber’s Comb

To cut longer hair, hold it up with the barber’s

comb and cut it with the scissors or with

clipper (the Guide Comb must be removed

from the clipper).

Trimming with the Thinning Guide

The Thinning Guide is a device that allows

you to thin a chosen part of the hair rather

than trim it all at the same length. By rotating

the Turning Wheel for actuating the thinning

guide a metallic blocker will come forward

and block a number of teeth of the clipper.

So that when you cut hair with the Thinning

Guide, some of the hair gets between the

teeth of the clipper and is cut, but most of the

hair falls in the gaps between the teeth and

is not cut. This allows some of the hairs to be

cut short and other hairs to remain at the full

length of the style. With some of the hairs cut

short, this thins out the hair.

1. Remove the Guide Comb.

2. To actuate the Thinning Guide, rotate the

Turning Wheel to “IıIıI“.

3. Lift hair with the Barber’s Comb or

fingers to desired length and cut hair with

the clipper.

CLEANING AND MAINTENANCE

(fig. 2)

• It is advised to clean the trimmer after

each use.

• Turn off the appliance and remove the

plug from the wall socket.

• Remove the Guide Comb.

• Pull out the razor head by pushing it

slowly backwards (fig. A).

• Remove hairs from the razor blades and

from holes in the appliance through the

cleaning brush.

• Apply 1-2 drops of the lubrication oil on

the cutter system (fig. B).

• The house of the appliance can be

cleaned with a damp cloth. Be sure no

water

• Is leaking into the appliance. Don’t ever

immerse the appliance into fluids (fig. C).

• The Guide comb can be cleaned by

rinsing them with warm water.

• Dry all parts before placing them back on

the appliance.

STORAGE

• Save the appliance in a dry dust free

space when not using it for longer time.

DISPOSAL

Protect the environment

These hair clippers contain two permanently

in-built Ni-MH rechargeable batteries.

Do not dispose of the batteries or the device

with normal household refuse, contact your

local council to find out about environmentally

friendly and proper disposal of the device(as

electrical scrap) observe the applicable local

and national disposal regulations with regard

to separation of materials, waste collection

and recycling centre.

The packaging is wholly composed of

environmentally friendly materials that can be

disposed of at a local recycling centre

The following parts should be disposed of

separately

1. Motor, metal parts, circuit board

2. Mains adapter

3. Plastic parts

4. Rechargeable batteries

REMOVING THE BATTERIES

Caution! Do not short-circuit the removed

batteries, they could become very hot if

they still hold charge. Dismantle the device

in the manner shown below to prepare it

for environmentally compatible disposal

disconnect the lead from the hair clippers

before dismantling.

1. Fully discharge the batteries by switching

on the hair clippers unless the motor

stops.

2. Remove the cutter head from the device

by pressing it off downwards.

3. Unscrew the two screws on the back

of the device using a small Phillips

screwdriver.

4. Unscrew the two screws near the drive

shaft using a small Phillips screwdriver

5. Remove the two grip panels, one

from each side using a flat-headed

screwdriver may help in doing this.

6. Pull the cutter head frame off the device

to do this the two plastic release buttons

must first be disengaged internally which

allows the cutter head frame to be pulled

downwards.

7. The two adjustment wheels can now be

easily slipped off upwards.

Separate the two halves of the housing

the drive module with the batteries is

now easily removed.

8. Cut all the wires using pliers, the

rechargeable batteries can now be

removed and taken to a suitable

collection point for disposal.

Recycling

This product bears the selective sorting

symbol for waste electrical and electronic

equipment (WEEE).

This means that this product must be

handled pursuant to European Directive

2002/96/EC in order to be recycled or

dismantled to minimize its impact on the

environment.

For further information, please contact your

local or regional authorities.

Electronic products not included in the

selective sorting process are potentially

dangerous for the environment and human

heath due to the presence of hazardous

substances.

Service centre

If the product doesn‘t function properly,

please contact your dealer or an authorised

service centre.

SPECIFICATION:

Power: 230V • 50Hz • 6W

ENGLISH

ENGLISH

M_5676-1_v01.indd Abs1:4-Abs1:5M_5676-1_v01.indd Abs1:4-Abs1:5 2010.4.14 1:27:42 PM2010.4.14 1:27:42 PM

التقييم

المزيد عن دليل المستخدم هذا

نحن ندرك أنه من الجيد أن يكون لديك دليل ورقي لـ ماكينة قص الشعر FA-5676-1 First Austria الخاص بك. يمكنك دائمًا تنزيل الدليل من موقعنا الإلكتروني وطباعته بنفسك. إذا كنت ترغب في الحصول على الدليل الأصلي، فنوصيك بالاتصال بـ First Austria. قد يكون بمقدورهم تقديم دليل أصلي. هل تبحث عن دليل ماكينة قص الشعر FA-5676-1 First Austria الخاص بك بلغة مختلفة؟ اختر لغتك المفضلة على صفحتنا الرئيسية وابحث عن رقم الطراز لمعرفة ما إذا كان متوفرًا لدينا.

تحديد

كافة الأدلة لـ ماكينات قص الشعر First Austria
المزيد من أدلة ماكينات قص الشعر

الأسئلة المتداولة حول ماكينة قص الشعر FA-5676-1 First Austria

يبحث فريق الدعم لدينا عن معلومات مفيدة عن المنتج وإجابات على الأسئلة المتكررة. وإذا وجت عدم دقة في أسئلتنا المتكررة، فيرجى إخبارنا بذلك عن طريق استخدام استمارة الاتصال بنا.

منتجات ذات صله

كتيب

ماكينة قص الشعر FA-5676-2 First Austria

كتيب

Philips HC3510 ماكينة قص الشعر

كتيب

Adler AD 2834 ماكينة قص الشعر

كتيب

ماكينة قص الشعر HC9100 Heritage Remington

كتيب

ماكينة قص الشعر HC5900 Precision Cut Remington

كتيب

Remington HC450 ماكينة قص الشعر

كتيب

Philips HC5650 ماكينة قص الشعر

كتيب

Philips HC7650 ماكينة قص الشعر

فئات ذات صلة