Home > الحدائق والشرفات > ماكينات تقليم حشائش > EGO ماكينات تقليم حشائش > EGO STA1500 ماكينة تقليم حشائش

كتيب EGO STA1500 ماكينة تقليم حشائش

هل تحتاج إلى دليل لـ EGO STA1500 ماكينة تقليم حشائش الخاص بك؟ يمكنك أدناه عرض وتنزيل دليل PDF باللغة العربية مجانًا. يحتوي هذا المنتج حاليًا على 0 من الأسئلة الشائعة، و0 من التعليقات، كما حصل على 0 من الأصوات. إذا لم يكن هذا هو الدليل الذي تريده، يرجى الاتصال بنا.

هل منتجك معيب ولا يقدم الدليل أي حل؟ انتقل إلى Repair Café للحصول على خدمات الإصلاح المجانية.

كتيب

LINE TRIMMER ATTACHMENT — STA15008

MAINTENACE AND STORAGE

◾ Disconnect the machine from the power supply

(i.e. remove the battery pack) before carrying out

maintenance or cleaning work.

◾ Use only the manufacturer’s recommended

replacement parts and accessories.

◾ Inspect and maintain the machine regularly. Have the

machine repaired only by an authorized repairer.

◾ When not in use, store the machine out of the reach

of children.

OTHER SAFETY WARNINGS

◾ Avoid Dangerous Environments – Don’t use

appliances on damp or wet slope.

◾ Keep guards in place and in working order.

◾ Keep hands and feet away from the cutting area.

◾ To reduce the risk of injury, never work on a ladder

or on any other insecure support. Never hold the

cutting unit above waist height.

◾ Check the cutting unit at regular short intervals

during operation, or immediately if there is a

noticeable change in cutting behavior.

◾ For best results, your battery should be charged in a

location where the temperature is greater than 5° C

and less than 40° C. Do not store it outside or in vehicles.

◾ If you are approached, stop the motor and cutting unit.

◾ Warn the operator of the danger of blade thrust

(only using with 3-teeth blade).

◾ Blade thrust may occur when the spinning blade

contacts an object that it does not immediately cut.

◾ Blade thrust can be violent enough to cause the unit

and/or operator to be propelled in any direction, and

possibly lose control of the unit.

◾ Blade thrust can occur without warning if the blade

snags, stalls or binds.

◾ Blade thrust is more likely to occur in areas where it

is difcult to see the material being cut.

◾ Do not attach any blade to a unit without proper

installation of all required parts. Failure to use the

proper parts can cause the blade to y off and

seriously injure the operator and/or bystanders.

Discard blades that are bent, warped, cracked,

broken, or damaged in any way. Use a sharp blade

A dull blade is more likely to snag and thrust

(only using with 3-teeth blade).

◾ A coasting blade/line can cause injury while it

continues to spin after the motor is stopped or

trigger is released. Maintain proper control until

the blade/line has completely stopped rotating.

◾ Battery tools do not have to be plugged into an

electrical outlet; therefore, they are always in

operating condition. Be aware of possible hazards

even when the tool is not operating. Take care when

performing maintenance or service.

◾ Do not wash with a hose; avoid getting water in

motor and electrical connections.

◾ If situations occur that are not covered in this

manual, use care and good judgment. Contact the

EGO Customer Service Center for assistance.

◾ Use only with battery packs and chargers listedin g.A

SAVE THESE INSTRUCTIONS!

SPECIFICATIONS

Cutting Mechanism Bump Head

Line Diameter

2.4 mm nylon

twist line

Cutting Width 38 cm

No-Load Speed 5000/6000 min

-1

Weight (Without battery pack) 1.59 kg

Recommended Operating

Temperature

0°C-40°C

Recommended Storage Temperature -20°C-70°C

Measured sound power level L

94.6 dB(A)

K=1.80 dB(A)

Sound pressure level at operator’s

ear L

83.2 dB(A)

K= 3 dB(A)

Guaranteed sound power level L

(measured according to

2000/14/EC)

96 dB(A)

Valuation of

vibration a

Front-assist handle

1.1 m/s

K=1.5 m/s

Rear handle

1.4 m/s

K=1.5 m/s

◾ The above parameters are tested and measured

equipped with power head PH1400E.

◾ The declared vibration total value has been measured

in accordance with a standard test method and may be

used for comparing one tool with another;

◾ The declared vibration total value may also be used in

a preliminary assessment of exposure.

NOTICE: The vibration emission during actual use of the

power tool can differ from the declared value in which the

tool is used; In order to protect the operator, user should wear

gloves and ear protectors in the actual conditions of use.

التقييم

‫قم بإخبارنا عن رأيك في EGO STA1500 ماكينة تقليم حشائش عن طريق ترك تقييم للمنتج. هل تريد أن تشارك بتجاربك مع هذا المنتج أو طرح سؤال ما؟ يرجى ترك تعليق في أسفل الصفحة.

هل أنت راض عن EGO STA1500 ماكينة تقليم حشائش؟
نعم لا

كن أول من يقيم هذا المنتج

0 الأصوات

انضم للمحادثة المتعلقة بهذا المنتج

هنا يمكنك مشاركة رأيك حول EGO STA1500 ماكينة تقليم حشائش. إذا كان لديك سؤال، فاقرأ الدليل بعناية أولاً. يمكن طلب الدليل باستخدام نموذج الاتصال الخاص بنا.